Semi Inlet

Handyman tips-washing machine maintenance

WASHING MACHINE
The number of times a washing machine is used and the speed at which the spin cycle revolves,if it were a car with
a speedometer it would have gone “round” the clock several times.
There is probably no greater and more worthwhile invention of modern times like it.
Take this scenario:Everybody ha sto wear clothes which have to be washed,just like everybody needs to eat..
BASIC WORKINGS
When you turn on the machine the inlet valves open to allow water to flow into the mahine by way of the detergent dsipenser
When the water reaches the required level it triggers the pressure switch that closes the inlet valve,which in turn
activates the element that heats the waterto the required selected temperature.
The heating element switches off and then the motor begins to turn the drum where the clothes are in.
At the start of the wash,the drum revolves slowly at first mixing the clothes together with the water and detergent
At intervals,the pump empties the machine and refills it with fresh water.
Final wash allows you to add fabric conditioner
The drum then spins the load at full speed to empty the water and semi dry the clothes.
The unique thing about all washing machines is that the locking switch on the door prevents anyone from opening the machine mid wash.
The water in the machine is emptied via a hose which is either attached to the outlet pipe of the sink,bath or kitchen or as a stand
alone pipe directly connected to the drains.
An important factor of all washibg machines is that you must not overload the machine,but there must be some “free” movement within
the drum-as a rule if you can get both hands into the top of the drum with ease after you have loaded the machine, then ther is
enough space left for the clothes to spin around freely.
MAINTENANCE
1.After use-clean the door seals and drum-keep the plastic around the drum dry,otherwise it will develop a black mould like fungus.
2.wipe and wash the detergent dispenser after every use.
SPOTCHECKS
1.Are the hoses behind the washing machine straight and not bent thereby stopping water from going into the machine?
2.Is the door closed,did you hear it “click” shut?
3.Are the stopcocks that allow water to flow into the machine on? These are usuallt coloured “red” for hot water and “blue” for cold
4.Have you switched the machine on??
5.Have you selected the correct setting?

TROUBLESHOOTING
machine will not spin

1.faulty motor-get a new one if you know how to fit one otherwise call the engineers
2.Slipping drive belt-locate the drive belt at the back of the machine and replace or call the engineers
3.Wrong programme setting check settings
4.Faulty door lock-press door firmly and operate machine if it works then the door is faulty if not then you need a new door lock-time to
call the engineers.

machine does not empty

1. Faulty pump-replace pump-or call the engineers.
2. Filter blocked-remove and run under the tap to clean
3. Outlet hose blocked or bent-flush out hose and check for items logged in hose.

water leaks from the machine

1.worn door seals-replace door seals,or call the engineer
2.worn hoses-check the condition of all the hoses and replace if necessary.

noisy machine

1. sharp objects in the drum like keys,nails,coins etc.
2. faulty door-check or call the engineer

excessive vibration

1.The machine is not level-place a spirit level on top of the machine and adjust the feet under the machine until level.
2 The concrete counterbalance ha sbecome loose-tighten with a spanner
3.Too much clothes in the machine-remove some of the clothes and rewash

door will not open

1. Faulty door switch-replace or call the http://www.handymantips.co.uk>engineer2. Water remains in the tub-drain and try to open.

machine does not fill up

1. bent or “kinked” hose-rectify
2. inlet valve filter blocked-this is the red and fry hose that goes at the back of the machine-remove and check the filters.
3. a faulty water level switch-call the engineer.

machine does not heat up

1.faulty heating element-call the engineer
2.faulty thermostat-call the engineer to test all the connections

About the Author

Handyman tips is a free online home improvement resource center helping you to repair,maintain and improve your home
more home improvement tips at :htp://www.handymantips.co.uk

LUXURY CONDO AT INLET YACHT CLUB ON INTRACOASTAL W/ DEEDED BOAT SLIP IN NEW SMYRNA BEACH, FL

1 HP Electric Centrifugal Water Pump $48.02 Our high quality 1 HP Electric Centrifugal Clear Water Pump features: 1 HP, 110 volt, 750 watt, 60 Hz, 3400 RPM Motor, Clear water operation, Capacity: 36 liters per minute, Maximum Suction Lift: 8 meters, Maximun head: 50 meters, Pump inlet and outlet: 1.5″, Overall unit measurement: 11 1/2″ x 7 ” x 5 1/4″, Heavy Duty Steel and Aluminum Construction…

DuroMax XP652WP 2-Inch Intake 7 HP OHV 4-Cycle 158-Gallon-Per-Minute Gas-Powered Portable Water Pump (CARB Compliant) $189.99 Move Huge Volumes of Water with this Smooth Running, Easy Starting, Long Lasting Pump Use to drain a pool in no time, empty a flooded basement, pump out a flooded trench, fill or empty a water storage tank or reservoir, irrigate a field, hose down a construction site, help drain a levy breach & more uses. This DuroMax 2-Inch water pump has a Real 2-Inch NPT fitting so you can use your regular hose…

Champion Power Equipment 65525 2-Inch Gas Powered Semi-Trash Water Pump With Hose Kit (CARB Compliant) $269.00 The Champion 2 inch Semi Gas Powered Water Pump provides dependable, portable water or solid pumping capabilities for your home, farm or jobsite. It has a 2 inch NPT inlet/2 inch NPT outlet with 158 gallon/minute maximum volume delivery and 3/4-inch maximum solid diameter. It is powered by a Champion 163 OHV engine with cast iron sleeve with 1 gallon gas tanks and is EPA approved (not for sale in …

Hushpower DBX Center Inlet/Outlet 6 x 14 Case 304S Stainless Steel Moderate Sound Muffler …